Loading…
triptopkit

Trinity Trip Top Kit – Sold Out – Feb. shipping

Details

Based on several years of vintage Ampeg B15 designs, the Trip Top combines the original circuits of both the Ampeg B-15NC (1964) as well as the later B-15NF (1965-67). The B-15-NF channel has the volume control section before the tone stack and in the B-15-NC channel it is after. Maintaining these circuits keeps the same gain structure and biasing found in the original B-15N amp designs, helping to preserve their true heritage. It also has two power supply settings – Cathode and Fixed bias to provide further tone structure.

The Trip Top is designed to output approximately 30 watts in cathode bias mode and 40 watts in fixed bias mode.

I play bass in an old-school Country band, and we do a live radio show on Saturday mornings.
I took the amp with me last Saturday, and although I didn't use it on the show our pedal steel player tried it out. He said it was the cleanest amp he's ever heard. He pushed it quite hard, and the attack from that instrument has many amps running for the door. No clipping, no drop outs, great sound.

Thanks for a great product !

Robert S. ,Burns, TN, USA (Trip Top)

The TRIP TOP is effectively four amps in one, which you can alternate between channels and the simple flick of the bias switch.
It has two channels each have volume with a ‘Pull Bright’ switch, treble and bass controls. The first channel, NORMAL, from the B-15-NF, has the volume control section before the tone stack. The second channel, CASCADE, comes from the B-15-NC which has the volume control section after the tone controls. The power amp section has two switch selectable bias modes – fixed (B-15NF) and cathode (B-15NC). While 1N4007 solid state rectifier diodes were used for the “NB” configuration, this was not incorporated into the design.

The Trip Top is built using point-to-point wiring using turret board construction for optimal service and reliability. High-quality coupling capacitors and resistors are selected for maximum tone, performance and reliability. The Trinity Amps power transformer and output transformer are all custom built and selected for maximum tone, performance and reliability.

Features

What differentiates our kits from others is part quality, fit, documentation and support. Included is all components; Mallory 150M caps; CARBON FILM and CARBON COMPOSITION resistors; SWITCHCRAFT or CLIFF jacks, ALPHA pots, JJ 50/50uf filter cap; Belton Micalex tube sockets, tube retainers & shields; 1/8″ thick GP03 Turret Board with large size KEYSTONE Turrets; CARLING switches; high current impedance switches; All 22 gauge hook-up Wire; Pre-twisted heater wire; BELDEN Co-Ax cable; All Mounting hardware, spacers and nuts; 3 Inputs; AMPEG style control knobs; Pre-Cut 0.06″ MIRROR FINISH STAINLESS STEEL Chassis with tapped holes for mounting screws; SILK SCREENED Front and Rear chassis labels; CNC punched, Powder Coated Tube Cage; Detailed Assembly guide; large 11″ X 17″ size layout and schematic drawings and REAL Support.

Also included in the kit package is our Highly Rated, Custom Made Transformer set by Heyboer. 110V, 120V 60Hz / 220V, 230V, 240V 50Hz Primaries It is built to our specifications but based on original AMPEG transformers used in the early B15 amps. The Power transformer is rated at 300 mA compared to under 200mA originals and all other current third party suppliers including Ampeg’s re-issue. The output transformer has 3 Interleaves and heavier gauge winding than originals and multiple secondary windings (4, 8, 16 ohm support). This is an excellent B15 transformer. With our over spec’d and non-potted iron, you can optionally run KT88 POWER TUBES increasing the power output. The Trinity Amps power transformer and output transformer are all custom built and selected for maximum tone, performance and reliability.

Reviews

Running KT88s in the Trip Top –  Rob Brotherson

Long term update:

I can not recommend this amp highly enough. You guys hit this one out of the park!

After almost 3 years and hundreds of hours of playtime, there has been zero problems with my TripTop. The only issue is that the KT88s are too close together and it sounds like Trinity has addressed this point with wider spacing between tubes on the chassis. On the original chassis, I have the tubes separated using the red gasket rings but so much heat is generated that they have melted. The tubes have not exhibited any problems though.

I ran 6L6GCs in it for the first year. It has been run for the last 2 years on KT88s. Even with the KT88s, the power transformer is barely warming.

In case anyone is interested, I took some bench measurements on it tonight. All measurements were taken using the normal channel. Fixed bias was used, cathode bias resulted in lower values. Bias on each set of tubes was set to 70% dissipation.

Voltage output did not vary much when frequency was varied but both tubes lost a bit of output as frequency dropped below 500Hz. In both cases it was less than a volt down to 50Hz. A 4 ohm resistor was used as the output load. Measurements were taken using an oscilloscope at the point of visible distortion in the waveform. Higher power is possible with distorted waveforms.

I used the following formula to calculate power out: (Vp-p/2 * 0.707)^2 / 4 ohms

To summarize my results:

KT88

Diode Rectification

Plate Voltage = 490 Vp-p

Bias Current = 50 mA

Peak voltage = 46.0 Vp-p at 1KHz

Output Power = 66.1 Watts

6L6GC

GZ34 Rectifier

Plate Voltage = 473 Vp-p

Bias Current = 43 mA

Peak voltage = 40.4 Vp-p at 500Hz

Output Power = 51 Watts

 

Great amp. Great Sound. Buy one.

Specifications

  • Channels: 2
  • Controls Normal: Volume/Bright; Treble; Bass
  • Controls Cascade: Volume/Bright; Treble; Bass
  • Power output: 25-30 watts in cathode bias mode and 35-40 watts in fixed bias mode
  • Preamp Tubes Required: 3 – 6SL7-GT
  • Power Tubes Required: 2 – 6L6
  • Rectifier Required: 5AR4
  • Bias: Fixed or Cathode (selectable)
  • Choke: no
  • Outputs: 2
  • Speaker Output: 4, 8, 16 switched
  • Weight: Head: 26 lbs.
  • Switches: Cathode / Fixed bias; Hum Control; Bias Setting
  • Other: Pre-amp Out
  • Construction: Mirror Finish Stainless Steel .06 inch thick Chassis with silk-screened front /rear labels ;
  • Chassis Dimensions: Head: 2.5” H x 17” W x 10” D
  • Options: CNC fabricated Black Powder Coated Tube Cage

Pricing Options

Canadian Customers Click 'Inquire' to receive up-to-date CAD pricing and shipping. Include postal code for quote.
$ CAD
We price affordably while managing fluctuating exchange rates with our suppliers. Our CAD best price guarantee accurately reflects our costs.
Trinity Trip Top Kit
$935 USD
Trip Top kit includes all components plus tube cage. No tubes, speaker or cabinet.
Custom Trip Top Head Cabinet
$382 USD
Trip Top Portaflex Cabinet, no speaker
$750 USD
Cabinet Cart
$158 USD

Add to Cart

Trip Top Kit deposit

To Purchase Items

  1. Select an item using the drop down menu.
  2. Add the item to your shopping cart using the Add to Cart button.This will take you to your shopping cart.
  3. If you wish to purchase additional items, e.g. a transformer set, click Continue Shopping. This will return you to the Trinity Amps site.
  4. Select the next item you wish to purchase using the drop down menu and repeat from Step #2.
  5. When you are finished shopping, wish to check and are viewing your shopping cart, click either PayPal Check out or Check Out (Pay without a PayPal account).
  • To view your shopping cart click View Cart on the Trinity Amps site and then check out using one of the aforementioned process.
  • Be sure to include your phone number with your order.
  • Shipping outside of North America will be adjusted and an email sent with details.

Inquire

Your Name
E Mail:
Subject:
Message:

Payment Information

Payments can be made through PayPal to sales@trinityamps.com. Payments can also be made using Interac e-Transfer, money order, cashier’s or personal check to Trinity Amps Inc.

We accept Canadian credit cards at our shop or by phone.

If you are located outside of Canada and want to make a payment using a VISA or Mastercard, an invoice will be provided using PayPal’s credit card service. No PayPal account is required.

Please be sure to send your full shipping address and contact phone number when ordering. If you have any questions, please contact us for more information, visit our web site or forum.

All prices are listed in US dollars. Orders ship from Brighton, Ontario, Canada, applicable taxes not included. Specifications and prices subject to change without notice.

Trinity Amps Inc.
165 Kanata Dr.
Grafton, ON
Canada
K0K 2G0

+1-905-373-6571 Canada, EST

Links